Geeetechi3b 3D model for printing: 13 results found

Displaying 1 - 13 of 13
  • Free
  • Updated! Prusa i3 E3D v6 / lite6 Bowden Mount for 30mm carriage (Geeetech/CTC/Euroway etc)

    Updated! Prusa i3 E3D v6 / lite6 Bowden Mount for 30mm carriage (Geeetech/CTC/Euroway etc)thingiverse.com
    Updated! Prusa i3 E3D v6 / lite6 Bowden Mount for 30mm carriage (Geeetech/CTC/Euroway etc)
    Category: 3D PRINTING / Prusa
    Tags
    113786Free

    Bracket for Y axis with new End stop from Geeetech

    Bracket for Y axis with new End stop from Geeetechthingiverse.com
    Baught new end stops and needed a new bracket. If you got the same printer and are looking for better end stops look here: http://www.geeetech.com/mec
    Category: none
    Tags
    16137Free

    GEEETech MK8 Printhead Fan Shroud ver.3 (compact)

    GEEETech MK8 Printhead Fan Shroud ver.3 (compact)thingiverse.com
    A revised version of my GeeeTech Prusa i3 Acrylic print cooler duct that mounts to the MK8 Extruder - My MK8 extruder came with a cooling block that
    Category: none
    Tags
    333KFree

    extruder fan air channel for geeetech prusa i3 mk8 & AutoLevel

    extruder fan air channel for geeetech prusa i3 mk8 & AutoLevelthingiverse.com
    I have re made the Extruder fan by "thegman" with the following modifications: intake is closer to the heat sink. output port is direct
    Category: none
    Tags
    13207Free

    Geeetech I3 pro 8mm Acrylic X, Y pully guide

    Geeetech I3 pro 8mm Acrylic X, Y pully guidethingiverse.com
    Please see below update When the X, Y pulley are not centered correctly, the belt slowly moves to one side till it gets stuck and then your lose your
    Category: none
    Tags
    12413Free

    Geeetech i3 idler with Bowden extruder holder

    Geeetech i3 idler with Bowden extruder holderthingiverse.com
    I have made Bowden extruder for my Geeetech Acrylic i3. The best way to mount extruder is on the idler place, so PTFE tube has minimal lenght
    Category: none
    Tags
    40302Free
    This is a slightler stronger extruder mount for the i3 it has less flex than stock
    Category: none
    Tags
    18439Free

    Filament Reel Bearings for 1" PVC

    Filament Reel Bearings for 1" PVCthingiverse.com
    Upgrading my printer from a single color to a triple cone hotend extruder (the new Diamond) and wanted: 1) a way to change out filament spools a lot s
    Category: none
    Tags
    18201Free

    GEEETech Prusa i3b Acrylic - Front Switch Box from Z-axis stepper mounts (L&R)

    GEEETech Prusa i3b Acrylic - Front Switch Box from Z-axis stepper mounts (L&R)thingiverse.com
    Created switch mounts that mount off the front of the Z-axis steppers so that I could have more control and access switching easier than always reachi
    Category: 3D PRINTING / Prusa
    Tags
    171KFree

    40mm fan brackets for Mega 2650 & Ramps 1.4 (need 4 brackets for 2 fans)

    40mm fan brackets for Mega 2650 & Ramps 1.4 (need 4 brackets for 2 fans)thingiverse.com
    Customized version of http://www.thingiverse.com/thing:166045 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=16604
    Category: none
    Tags
    15176Free

    80mm fan bracket for Mega 2650 & Ramps 1.4 (need 2 brackets for 1 fan)

    80mm fan bracket for Mega 2650 & Ramps 1.4 (need 2 brackets for 1 fan)thingiverse.com
    Customized version of http://www.thingiverse.com/thing:166045 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=16604
    Category: none
    Tags
    19655Free

    Filament Guide for Tower Center - Prusa i3 8mm Acrylic

    Filament Guide for Tower Center - Prusa i3 8mm Acrylicthingiverse.com
    Made a filament guide in SketchUp for the top center of my GEEETech Prusa i3 Acrylic - this guide slips over the acrylic plate (8mm) and fits the fact
    Category: none
    Tags
    16198Free

    GEEETech Prusa i3b Acrylic X-axis adjustable endstop extension

    GEEETech Prusa i3b Acrylic X-axis adjustable endstop extensionthingiverse.com
    This clips over the top of the factory GEEETech Prusa i3b Acrylic X-axis and adds a 10-30mm extension with an adjustable screw to properly adjust the
    Category: none
    Tags
    12262Free