This chess set is designed to print on any 3d printer. Hollowed out design to cut down the cost for the more expensive resin and powder based printers. Already tested and printed successfully on a Makerbot (FDM 3d printer). Print on your home 3d printer, or upload the file to Sculpteo or Shapeways for professional 3d printing and delivery.These files can be streamed to your printer from Pinshape. just search for Faceted Chess Set!
This is a real working 1/4 scale BattleBot drone. The full sized model "AfterByte" can be seen on BattleBots:The Gears Awaken (2016).www.MBSrobotics.com www.battlebots.com/robot/basilisk/ This file was designed for the Form 2 and other Formlabs printers, see www.Formlabs.com  . We finished our first drone in a day with our Form 2, the prints required no drilling or sanding to fit the motors, wires, zip ties etc.*Step 1**Prep and print the files*: We have designed our .stl's to work with many different motors simply by scaling the file. If you plan to use our parts list, you will want the files scaled by 50%, final file sizes should be:Wing - 75.04x65.92x204.7mmFlight Body - 109.64x52.85x130.16mmFight Body - 109.64x125.97x117.32mm*Step 2**Order Parts*: Hobby King = friend :D4x Motor  = $35.604x ESC- motor controller  = $40.401x Lipo Battery Pack  = $9.992+x Carbon Fiber Propellers  = $7.361x Naze32 Flight Controller  = $19.99TOTAL: $113.34If this is your first drone, you will also need a Flight Remote  and Battery Charger .*Step 3**Body Assembly + Motor wiring*: You will need a bit of epoxy to hold the body and wings together. The channel in the arms is easily big enough to handle the wires from the motors, but not much else. For our installation we cut the banana plugs off the motor leads and soldered all three wires to a guide wire (1m). We then ran this guide through the motor cradle hole. By gently pulling the guide, the motor wires will follow with little resistance. *Step 4**ESC + Logic Wiring*: If your building the Flight Body, get that flight controller in early! the more wires you have down there, the harder it will be to install. The ESC's will be soldered directly to the motor wires you pulled through the frame. By default the motors should spin counter clockwise, just cross any two motor wires to change the motor direction. Just logic and battery wiring left*Step 5**FLY!!!!!: *And try not to crash. Maybe pick up a $30 micro drone to practice before smashing your beautiful drone. http://www.MBSrobotics.com http://www.battlebots.com/robot/basilisk/ http://www.Formlabs.com http://www.hobbyking.com/hobbyking/store/__61433__DYS_BE1806_2300kv_Brushless_Multirotor_Motor_2S_3S.html http://www.hobbyking.com/hobbyking/store/__2161__TURNIGY_Plush_12amp_2A_BEC_BESC.html http://www.hobbyking.com/hobbyking/store/__8932__Turnigy_2200mAh_3S_20C_Lipo_Pack.html http://www.hobbyking.com/hobbyking/store/__66683__Quanum_Carbon_Fiber_T_Style_Propeller_5x3_CW_CCW_2pcs_.html http://www.hobbyking.com/hobbyking/store/__68813__AfroFlight_Naze32_Acro_FunFly_Controller_Soldered_version_Horizontal_Pin_.html http://www.hobbyking.com/hobbyking/store/__8338__Hobby_King_2_4Ghz_4Ch_Tx_Rx_V2_Mode_2_.html http://www.hobbyking.com/hobbyking/store/__49338__Turnigy_E3_Compact_2S_3S_Lipo_Charger_100_240v_US_Plug_.html
3D Printed in dry-bone white, this delicate 5 1/2 inch Sea Bream is included in the Limited Edition version of Shriekback’s March release album; “Without real string or fish”http://shriekbackmusic.tumblr.com