Let’s make our bike individual by using the opportunities given by 3D printing! I used an average textile production technique, weaving to reach the aim. Until now in the industry we could only produce woven goods (Cloth, woven basket) from those materials which are flexible. The bycicle tyre designed by me, can be produced from either plastic or metal which meets the steadyness standpoints and aesthetically gives positive experience to the user and his surroundings. On the applied radial woven threads, instead of spokes, you can observe constantly changing diameter along the radius direction which can be realized by the 3D printing technology. The flexible, solid, non inflatable tyre would be made up of layers with different flexibility printed upon each other.
This is just one part of World Cup 2014 collectionFigures are 3D printableSpainhttps://b2b.partcommunity.com/community/partcloud/index#!part?name=Table+Soccer+figure+-+Spain&model_id=40225 Germanyhttps://b2b.partcommunity.com/community/partcloud/index#!part?name=Table+Soccer+figure+-+Germany&model_id=40211 Brazilhttps://b2b.partcommunity.com/community/partcloud/index#!part?name=Table+Soccer+figure+-+Brasil&model_id=40229 Croatiahttps://b2b.partcommunity.com/community/partcloud/index#!part?name=Table+Soccer+figure+-+Croatia&model_id=40215  https://b2b.partcommunity.com/community/partcloud/index#!part?name=Table+Soccer+figure+-+Spain&model_id=40225 https://b2b.partcommunity.com/community/partcloud/index#!part?name=Table+Soccer+figure+-+Germany&model_id=40211 https://b2b.partcommunity.com/community/partcloud/index#!part?name=Table+Soccer+figure+-+Brasil&model_id=40229 https://b2b.partcommunity.com/community/partcloud/index#!part?name=Table+Soccer+figure+-+Croatia&model_id=40215
Old stile BoomerangYou need to use 240 deg, 80 - 100 % infill, 2 lines at .10mm and 40mm on extrude and 130mm on travel.Boomerange  by JML31347  is licensed under the Attribution - Non-Commercial - No Derivatives  license. https://www.thingiverse.com/thing:751793 http://www.thingiverse.com/JML31347 http://creativecommons.org/licenses/by-nc-nd/3.0/
Otterbox iPhone Belt Clip Mod to Mountain Bike Mountyoumagine.com
I've wanted to be able to mount my phone to my Cannondale F9 since I first purchased it and could never find a way to do so without a big clunky attachment, without having to buy a completely different case with its own proprietary mounts, or one that wasn't held together with double sided tape. So I finally got around to designing one that fit my purpose. I use the TrackMyRide+ App alot so this makes it easier to both see calls and handle your phone without having to pull it out of your pockets while riding. Or you could even watch a movie on the go! :PThe version pictured is my first version which has worked great and has held my phone safely for over 60 miles of riding. I've uploaded V2 which reduces the amount of material necessary to print it and should still give a good solid hold.Quick Instructions:1) Print the adapter. ( I used 2mm walls with a 80% infill ) I added a small pilot hole in the center of the adapter to force Cura to create a 4mm~ area of material around the center to make the use of a screw attachment easier for those who use less infill ( ie: 20% ). The center pounchout may need a little cleaning with a dremel of any support material to help the otterbox clip sit flush in the hole.2) Carefully bend and pry away the original plastic gator clip from the Otterbox Belt clip exposing the circular attachment point. I used a small pair of need nose pliers.3) Align the adapter on your belt clip ( assuring a flush fit ) in the orientation you would like to mount your phone to your bike and using a small drill bit, drill a pilot hole with your drill about 4-5mm .4) Find a way to countersink your hole so that your screw can sit flush behind the phone. ( Use a countersink or large dril bit tip )5) Install your screw and test fit it on your bike.6) If all is well, back out the screw just enough to remove the adapter and apply generous amounts of ABS juice or adhesive to both mating surfaces. Grab both pieces and align them and press them together as you install the screw again by hand. At this point using wood workers clamps you can clamp down on the adapter and belt clip plate. Use a small brush to add a light coat of ABS juice along the seam of the adapter plate and belt clip to help make it stronger.7) Give the adhesive 24 hours to dry and harden. Once dry, run your zip ties through the two holes and mount it on your bike. Make sure to pull the zip ties nice and tight. Another tip is to run the zip ties in opposite directions to keep the base from wanting to pull to one side.
Bicycle reflector and taillight mountsyoumagine.com
UPDATED 2014-09-02 made clip wider and printed on its side for better durability - original design snapped on me after a couple of days.I fitted a rear rack on my road bike and intend to use a trunk bag or garment bag there, both of which will block a taillight on my seat post, so I needed to mount my light elsewhere.The rack has a good mount position, it's a standard reflector bracket.The "reflector.stl" here will screw to a standard reflector bracket using the #8 screws in the BoM. The "pulseclip.stl" is a small clip that snugly holds an Axiom Pulse 60 taillight (I highly recommend this light BTW, great value for money and probably the best < $50 bicycle taillight on the market).Note that there's no retention clip as such on this bracket, it does not "snap" into place, but it's quite snug and I feel it won't come out. If this becomes a problem I will redesign.I designed them as separate parts to be glued together to simplify printing. The SCAD can be modified if you have different size requirements.The pulse clip has integral support for the top rail when printing. Make sure to check your toolpath before printing and make sure the support layer prints with proper bridging. Slic3r didn't do it for me, I had to use Cura and cut down to 1 perimeter to get it to print right.If using these two together, glue them together after confirming that they both fit your equipment. I used epoxy, Gorilla Glue would probably be fine too.Note in the pictures I used a length of Spectra line to catch the light if it falls out. I really recommend a safety tether on your bike's equipment, I've lost > $100 in taillights over the years by having brackets break or just slip off.