Universal GoPro ski stick mountredpah.com
*Universal GoPro ski stick mount *lets you use your ski sticks like selfie monopod and shoot special videos during skiing or snowboarding :) Combine it with other GoPro mounts to obtain new abilities! You need only one additional M4 bolt with butterfly nut and one M5 nut. You can use this mount with sticks 16-20mm diameter.Print and enjoy! ))
Bebop Lens Hood for GoPro 37mm UV Filter Lensredpah.com
This is an adaptor to fix the bebop and the GoPro 37mm UV filter lens.After a crash with broken lens I decided to find a good solution.There is 1 mm difference between the GoPro lens and the inner diameter of the hood.It is on purpose.Use some black tape on the lens to increase adhesion.Lens + 3D printed hood around 20USDNew Bebop Camera: 8 times more expensive.
GoPro Hero 3 Gimbal for Multirotortrinpy.com
This model is designed to fit a GoPro Hero 3. It’s intended use is to create a gimbal for the GoPro so you can mount it to multirotors or anything else. It will provide you with a 2 degree of freedon gimbal that can be used with two 9g servos to provide roll and tilt or pan and tilt.
GoPro Ski Stick Mountredpah.com
*GoPro Ski Stick Mount* lets use your ski sticks like selfie monopod and shoot special videos during skiing or snowboarding :) Combine it with other GoPro mounts to obtain new abilities! Now you will have more shooting directions!You need only one additional M4 bolt with butterfly nut and one M5 nut. You can use this mount with sticks 16-20mm diameter.Layer: 0.2mm, Infill: 100%, Support material: No, Brim: recomended 5mm. Print time ~45 min.Print and enjoy! ))
Shoei RF-1200 GoPro Chin Mountpinshape.com
SummaryThis is a mount meant for GoPro-style clips on the chin of a Shoei RF-1200. Uses VHB pads meant for GoPro mounts, available all over the web. MIGHT fit the RF-1100. Has a cut-out to accommodate opening the chin vent.This currently is a prototype (V6) and after riding with it I'll make some changes if they're necessary. I can make variations on this if needed.EDIT: Uploaded a V6, which should take up more of the room between the vent and the bottom of the chin, and hopefully lines up with a VHB pad slightly better. V6 has no vent-slider-notch as it seemed kind-of useless.Instructions3D scan with Skanect, reconstructed in Rhino, model built in Rhino, printed in S3D @ 50% infill, ABS, 110 plate 230 extruder. See gallery for where I printed supports - I also used a sticky disk (an 0.5mm thick disk under an object) because the sides are mostly flat.
GoPro SeatPost Mount (25.4mm)youmagine.com
A GoPro camera mount for the small diameter Cannondale Synapse 25.4 mm seatpost. Uses two 6/32 x 1/2 in screws and nuts to secure to the seatpost and a standard GoPro nut and thumb screw for the camera attachment point.Printed with the following settings to obtain a strong, but light (10g), mount:- ABS- 40% infill- 0.8 mm shell- 0.6 mm base- Brim- Support Touching build PlateI also tested this part with PLA and it worked file as well. With PLA, I needed to use a Raft instead of Brim support for the best print.
GoPro Lens Adapter To Gaoki X-Game Camera - AutoCAD - 3D CAD model - GrabCADgrabcad.com
Chest Mount Harness for GoPro cameraspinshape.com
Chest Mount Harness to use with you GoPro camera. I use a Hero 3 so i´m not sure how it will fit newer cameras like Hero 4.The Harenss Lock might be a bit bulky and maybe not the most clever solution but it works and i´m sure someone can come up with a great replacement!If you are thinking of using this it´s important to consider the conditions where you are about to use the mount. High or low temperatures for example can affect the durability of such a mount to the extent that it can break.Unfortunately there are so many variables that affects the quality of a print so i think it´s also important to say that if you use this mount it´s at your own risk. If unsure maybe it´s better to just buy one in the store.You need to 3D Print the following pieces:3 pcs Adjustment Buckle1 pcs Back Buckle1 pcs Chest Mount1 pcs Harness Lock Part 11 pcs Harness Lock Part 2And you need to buy:Approx 1,5 metres 50mm Nylon Webbing (I used about 1,5 meter, but of course that may vary depending of your size)Hopefully you can figure out how to put it together according to the pictures. =)www.danielnoree.com https://youtu.be/KpWhszjRqoc http://www.danielnoree.com
Superversatile GoPro Framemyminifactory.com
Hi everybody, this is a superversatile GoPro Frame, it was designed after the idea of inigosobrini. So as he said :"soo it s basically the frame but with the "arms" where you put the gopro in the four sides of the frame, so, for example, when you have to put it in your sticker mount in the side of the helmet, you dont have to use the 90º screws that can get loose and you have to take them in your bag and make it untidy. Its also really usefull to not put your camera upside down, and waste time changing settings, etc"
GoPro Hero Picavet Kite Mountpinshape.com
Although this picavet kite mount with captive pulleys for the GoPro Hero 3/3+ is designed for kite aerial photography as described on the Berkely KAP page (see http://www.arch.ced.berkeley.edu/kap/equip/picavet.html), it can be used for other applications requiring suspended rigging. Such as, for example, hanging your camera from a sailboat halyard.
GoPro Print Bed Mountyoumagine.com
Mount your GoPro camera to the moving bed. Mounts underneath the heated printing plate. Therefor heat will not effect the mount. The mount also clears the frame in full up and down positions. Glue the two parts together but it is not necessary as there is a good fit.Bed must be raised from advanced options to properly install. Re adjust your bed after installation. Possible to mount from side of bed closer to the supports. Use at your own risk. :)Print the bolted section with the 3 fins facing down. Print very slow in the first 5mm to avoid detaching the fins from the print bed. Use a freshly cleaned and leveled bed to print. I had best results on the rounds by printing on a clean and unheated print bed (PLA material used).Design Notes: I tried to vertically mount it with a swivel to allow for simple removal when the bed is lowered. I have the designs but due to clearance issues and the possibility of the print head striking the camera I moved away from that design. I can make it work, if I have time a V2 may be coming out soon.
Yodix For Goprocults3d.com
Yodix is a car for Gopro.It will allow you to shoot movies in a new light Have fun :)=> Downloadable file to print on your printerLayer height of 0.3 and 90% filling=> Parts are now separated to print them separately.Video demonstration :https://www.youtube.com/watch?v=x8NkJb4xJoc  https://www.youtube.com/watch?v=x8NkJb4xJoc