Spool holder 3D model for printing: 237 results found
Displaying 1 - 32 of 237
Simple Spool Holdertrinpy.com
SMALL - Universal Spool Holderpinshape.com
This is the page for my Small sized spool holder... This is for a specific size of my universal spool holder... The main page for this universal spool holder can be found below... That page has every size needed to fit 99% of the spools currently on the market...Main Page - http://www.thingiverse.com/thing:1001312If you're on this page, you've probably already been to the main page and decided the size you needed (which I assume is this size) so I won't go into too much detail here. But here is the instructional video on how to print and put the spool holder togetherhttps://www.youtube.com/watch?v=zG1CFx9aUIkFilamentChallenge
OVERSIZED - Universal Spool Holderpinshape.com
This is the page for my Oversized size spool holder... This is for a specific size of my overall universal spool holder... The main page for this universal spool holder can be found below... That page has every size needed to fit 99% of the spools currently on the market...Main Page - http://www.thingiverse.com/thing:1001312If you're on this page, you've probably already been to the main page and decided the size you needed (which I assume is this size) so I won't go into too much detail here. But here is the instructional video on how to print and put the spool holder togetherhttps://www.youtube.com/watch?v=zG1CFx9aUIkFilamentChallenge
The Universal Spool Holder - Main Pagepinshape.com
This is the main page for my universal spool holder design... This page contains every single file I have made and every derivative of the holder... I'm going to lay out instructions on how to get the perfect fit for your spools in the instruction tab... You can also watch the YouTube video below where I explain everything you need to know...https://www.youtube.com/watch?v=zG1CFx9aUIk&feature=youtu.beThere are three "sizes" (different length arms) for this spool holder... Every arm length is on this page in STL form, but to make it simpler and to avoid confusion, I made three separate pages for each sized holder (Small, Standard, Oversized)... When you watch the video or read the instructions you know what measurements to take to get the perfect fit... On a side note, if you want a truly, all around "Universal" holder - you can simply print two "OverSized" Arms and 110mm Rods... This will fit damn near every spool - it just wont be a tailored fit - and thus wont look pretty... This is why I decided to make three sizes - strictly for aesthetic reasons.Small - http://www.thingiverse.com/thing:1001360Standard - http://www.thingiverse.com/thing:943563OverSized - http://www.thingiverse.com/thing:1001359This is a full redesign of my popular, but old and relatively weak spool holder that I designed nearly two years ago...Old, Obsolete Spool Holder:http://www.thingiverse.com/thing:290064This new design is 100% better - I completely redesigned my screws and spinner bolts for better tolerance for 3D Printing... My old screws were good if they were machined, but they were way too fine to be 3D printed well... So I made the threading much better and made the screws much stronger... I also added a lot of structural features that I explain in the video...Here's a list of what I did in the new design.Made both arms (the base and the spinner) 2.5mm shorter in height, I also added fillets to every corner so every contour is nice and rounded.Redid the bolt pattern and made that easier on the hand while spinning the spinner bolt.Increased the diameter of the screws and added 45 degree chamfers for strength... Screws are very strong now.Redid all the threading... This will thread smooth and tight right off the printer - I had 100% success rate on prints.Added a hole on the lower Rods to hold ends of filament to keep them from unraveling or raveling in - resulting in getting the spool tangled up.This is now about a 33% decrease in total print time from my old design... Overall, it should take about 6-7 hours to print an entire holder on a standard .2mm layer setting... But you can speed it up by going .3mm and everything will be perfect... Infill is not a big issue... 15-20% should do it... If you want everything to look nice on the outside - do 3 perimeter shells.Other than all of that - this should work for everyone and will fit on 95% of spools... The only spool I know doesn't fit on this univeral holder is Taulman brand spools... But never fear, I made a spool holder specifically for Taulman Spools...You can find the Taulman spool holder here... http://www.thingiverse.com/thing:938437**I hope you find this spool holder useful... Thanks for reading... ENJOY!!!FilamentChallenge
Makerfarm Prusa i3v Spool Holder Extensionpinshape.com
I got some spools of filament in that were a little to big for the stock spool holder that comes with the Makerfarm 8" Prusa i3v, so I made a little extender for it to accomodate this.--Update--I have uploaded a Version 2 of the base that contains a cutout for the screw that can get in the way.--Update 2--I have uploaded a "short" version of the base which will not come so close to the Z-Axis rod, as well as a Version 2 that includes a tool holder. Additionally, I have uploaded a top piece with a cut for those rolls that have the filament coming through the center.
RobotDigg Spool holder with 608ZZ skate bearing insertspinshape.com
SummaryI could not find anything on Thingiverse that fit my RobotDigg PLA spools so I made this 4 mm thick spool holder, quick print. With a small mod you could adapt it to fit any 200 mm diameter spools. Fits 21.93 mm diameter skate bearings, nice friction fit with a taper at the back to keep the bearing from being pushed into the spool. The Robot Digg spools Have a 38.14 mm diameter hole. 104 mm from center to base so fits the 200 mm diameter Robot Digg spool. The cross members are a tight fit so tapping them on with a small hammer and a drop of crazy glue makes a nice strong connection. Leave the little bag of desiccant in the spool so it doesn't back spool, the bearings are very smooth. I'm using a 6.26 mm bolt in the pic but it is sized for 7.75 mm threaded rod.InstructionsPrint it, tap the cross supports on, put a drop of crazy glue at the connection. Press in the bearings, put them in the reel and thread a bolt or section of threaded rod with a couple washers through the whole thing. Leave the little bag of desiccant inside the spool so it doesn't back spool.