Filament dust filterredpah.com
with this part you can keep clean the filament (no dust inside the extruder) 1,75 or 3 mm on your printer. You can place it everywhere....up to you :-)size D24 x 13mmcut out a little piece of sponge (D20 x 10mm) and put it inside the sponge-holder...make sure that the sponge not opposes friction on the filament
Filament Clip for 1.75mmpinshape.com
I thought of a new design for filament clips, as the ones I have been using don't seem to stop the filament from getting tangled very well, and also are hard to find sometimes. This one won't let the filament wrap around, and it's hard to miss. Also: branded, because ;-)Let me know if you're interested in a 3mm version.
3D-printable split filament spool with threaded joint (135 mm)cults3d.com
This 3D-printable filament spool measures 135 mm i diameter (Ã¢ÂÂ 5 inches). Fully winded it contains approximately 350 grams of filament (Ã¢ÂÂ 12 ounces). It fits shafts with a diameter of 16 mm or smaller.The spool is made of two separate parts with a female and male threaded connection. The design can therefore be 3D-printed without the need of support material.As an accessory we also supply an axel which can be used with a power-drill to facilitate winding of new filament onto the spool.The video above shows how to assemble the 3D-printed spool and use a power-drill to fill it with TPU flexible rubber-like filament.
This small accessory can protect your FFF 3D printer filament from two common issues - cleaning and lubrication.A sponge wipes the filament clean from any dust particles and prevents them clogging the extruder.By dropping a few drops of common mineral oil on the sponge the filament passing through gets lubricated thus relieving the extruder motor from strain.Lubrication is specially useful if the filament needs to travel through long tubes before it enters the extruder.INSTRUCTIONS3D-print the provided STL file and insert a small piece sponge into the filament filter.Poke a hole into the sponge and make sure the filament passes through and comes out at the other end.Soak the sponge with a few drops of mineral oil (as for sewing machines, door hinges or bicycle chains).Place the filament filter somewhere in between the spool and the extruder. If you have a plastic tube which guides the filament to extruder (such as a bowden solution) make sure you place the filter before the filament enters the tube.See video for more information- http://youtu.be/rMDEsrgzC9M By Creative Tools- http://Creative-Tools.com - http://google.com/+CreativetoolsSe - http://twitter.com/CreativeTools - http://facebook.com/creativetools - http://youtube.com/creativetools - http://instructables.com/member/CreativeTools  http://youtu.be/rMDEsrgzC9M http://Creative-Tools.com http://google.com/+CreativetoolsSe http://twitter.com/CreativeTools http://facebook.com/creativetools http://youtube.com/creativetools http://instructables.com/member/CreativeTools
Filament Roll Holder / Bracketnunus-world.com
Bracket Designed as a filament roll holder. Bottom piece is 25mm x 75mm x 10mm. The long edge is 140mm long with a single hole for mounting a rod with a screw. The bottom two screws are spaced 1" apart and are 5mm Diameter to give some wiggle room with use with M4 screws. This could also be used as a simple bracket.Filament Roll Holder / Bracket  by rob0tuss1n  is licensed under the Creative Commons - Attribution  license.  http://www.thingiverse.com/thing:619578 http://www.thingiverse.com/rob0tuss1n http://creativecommons.org/licenses/by/3.0/
Ultimaker 2 filament guide with ball bearingyoumagine.com
- *"Bottom V1.0"* is printed with Support (Everywhere with Lines)Inner diameter of 0.24 mm are drawn largerSupport must be broken, top edge has to be slightly filed- *"Filament guide V1.0"* I have printed with 215 ° and layer height 0.1mmInner diameter of 0.24 mm are drawn largerBall bearings must be pressed fitThe ring at the bottom (see picture) must be broken, and flat surface can be easily straightened